HOMEPHOTOSCONTACT/TRAVELSCHEDULERESULTSSPONSORSPOINTSRULES

RACEIVERS ARE MANDATORY IN ALL DIVISIONS!
If you do not have one check out the link below to get one.
You will not be allowed to race without one. Make sure your
batteries are working before you pull out on the track and you are on the correct channel

Crate can run w/ the Late Models!
They have had wins against the regular late models.
Crates are very competetive @ CMS
Drivers be aware Crate can weight 2300 w/ crate tires!

Sportsman Crate 21 is allowed
Late Model D70 and Crate 21 is allowed


AMERICAN RACERS allowed @ Cochran Motor Speedway as of March 2010 are:
AMERICAN RACER 48
AMERICAN RACER 56
AMERICAN RACER 70
STOCKER MEDIUM
STOCKER HARD

6/19/09 Attention ROAD WARRIOR DRIVERS You CAN RUN 8inch wheels

LATE MODEL 2400 LBS IF YOU RUN A CRATE MOTOR 2300 CRATE 21 OK

3/12/09  2009  RULE BOOK AMENDMENTS

 

Ussery Drywall & Acoustical Ceiling Road Warrior

Page 12 - No experienced drivers

          4a. -  Section G. - Delete

                        Section H. - Delete

Section I. - 1850 stock holly, may remove choke plate from Holly or Quad-Jet only, no modification, use one carburetor spacer (1" Maximum) and two gaskets (maximum one 0.070 inch thick and one 0.250), one gasket between intake to spacer and one gasket between spacer to carburetor, rear metering plate OK.

Section J. - No pining studs. Eagle cast crank #50, and Eagle stock rods OK, cast iron water pump.

Page 13 -     Section M. - poly loks OK

                         Section P. - After market head bolts and washers OK

                         Section Q. - Racing pan OK

                         Section R. - Aluminum pulley OK

5. Transmission must be stock, Stock flywheel 20lbs., Clutch, Pressure plate 16lbs.

7. Stock suspension for make of car. No modifications of any kind (heating, cutting, spacers, stock away bar hook up, etc.) This means none. May set toe end and, cast and camber.

10. Minimum 4-point roll cage required and must be welded to frame rails and all connections must be fully welded. All cages must have a minimum of 3 horizontal bars, and is required in the driver's door and a minimum of 2 in the passenger door. Roll bar installation and workmanship must be approved. Loop bars from front to rear OK inside car.

12. Tires must be the same size. Steel wheels maximum 7 inches wide. Oversized 1-inch lug nuts required. Tire maximum width 8 inches. Bead locks on right side only. Tires on right front must be Baby Hoosier R4 or R6.

Page 14 -                                                                                                         

13. Fuel tank may be moved inside of trunk. Fuel cell highly recommended. May cut hole to mount fuel cell.

16. Weight

            Section A. 350 ci or less - 3500 lbs.

            Section B. 400 ci or more - 3600 lbs.


C & C Pawn City Cadet

Page 14 - 1. Car and Body

Section E. The stock steel unaltered floor pan, firewalls, trunk and trunk floor must be retained. Hulling permitted on hood, roof, trunk, and doors for roll cage and must retain rear wheel well. Trunk and floor pan cut out behind driver seat.

            Section I. Metric Monte Carlo may drill trailing arms to set pinion angle.

Page 15 -  Carburetor

                        Section D. - Delete

                        Section E. - Delete

Page 16 - Carburetor (continued)

                        Section G. - 3310 bowls OK.

Page 17 -

            6. Suspension

Section A. - Baby Hoosier tires RC 4 or RC 6.  8" wheels, Bead locks on right side only.

            7. Weight

                        Section A. - CMS Engine - 3300 lbs.

                        Section D. - Crate #602 - 3400 lbs.



Howell's Automotive Machinery Pure Stock

Page 17 -

•1.    Car and Body


Section H. - Fiberglass Hood OK.

Page 18 -

•2.    Tires and Wheels

Section A. - Delete

Section B. - Delete

Section C. - 8" or 10" Wheels, Baby Hoosier RC 4 or RC 6, Bead locks on right side only.

Page 19 -

            7a. CMS Engine

                        Section S. - Delete

                        Section W. - Aluminum water pump OK.

                Carburetor

                        Section E. - Quadrajet carburetor OK.

Page 20 -

            8. Weight

                        Section A. - CMS Engine - 3200 lbs.

                        Section B. - Crate motor part number P/N 88958602 - 3000 lbs.

Rim Rider Racing Graphics Sportsman

Page 22 -

            10. Wheels

                        Section C. - Beadlocks on right side only.

            11. Engine Specification

                        Section C. - Stock Diameter Lifters

Page 23 -      

               Crank, Rods, Intake & Carburetor

                        Section F. - I-Beam and H-Beam Rods OK.

                                    Heads - Bowtie Vortec OK

Page 24 -  

                                    Heads (continued)

                                                Section i. - Delete

                                                Section k.  - Any stud mounted Rocker Arm.

Page 26 -

            12. Weight

                        Section A. - Engine option 1: 492 Engine - 2550 lbs.

                        Section B. - Engine option 2: Crate Engine #602 - 2400 lbs.

                        Section C. - Engine option 3: Crate Engine #604 - 2500 lbs.

                        Section D. - Vortec Bowtie - 2700 lbs.

                        Section E. - Vortec 062 - 2600 lbs.


TIRES IN ALL CLASSES

Cadet - RC 4 or RC 6, 8" Hoosier                                     NLMS Tires - Spec. D-21 or D-55 Spec.

Road Warrior - Right Front, RC 4, 8" Hoosier                            NLMS Rules Apply - Ray Miller

Pure Stock - RC 4 or RC 6, Hoosier                                                         987-4219                   

Sportsman - Spec. D-21 or D-55 Spec.

NLMS Tires - Spec. D-21 or D-55 Spec

NLMS Rules Apply - Ray Miller 987-4219